Sains Malaysiana 53(8)(2024): 2003-2012

http://doi.org/10.17576/jsm-2024-5308-22

 

Kajian Histeresis Feroelektrik dan Pengutuban Dinamik bagi Seramik (Ba1-xCax)(Zr0.025Ti0.975)O3 dengan Penggantian Kecil Ca

(Ferroelectric Hysteresis and Dynamic Polarization Studies of Lower Ca-substituted (Ba1-xCax)(Zr0.025Ti0.975)O3 Ceramics)

 

NUR SOLEHAH ALI1, NOR HUWAIDA JANIL @ JAMIL1, NOR AMALINA AHMAD1,2, MOHAMMAD HAFIZUDDIN HJ JUMALI1,* & ZALITA ZAINUDDIN1

 

1Jabatan Fizik Gunaan, Fakulti Sains dan Teknologi, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia

2Pusat Pengajian Pra-Universiti, Universiti Malaysia Sarawak (UNIMAS), 94300 Kota Samarahan, Sarawak, Malaysia

 

Diserahkan: 6 Februari 2024/Diterima:  24 Jun 2024

 

Abstrak

Penyelidikan ini dijalankan untuk mengkaji kesan penggantian kecil Ca terhadap sifat feroelektrik seramik (Ba1-xCax)(Zr0.025Ti0.975)O3 (BCZT). Seramik BCZT disediakan menggunakan kaedah tindak balas keadaan pepejal dan disinter pada suhu 1350 °C selama 2 jam. Analisis XRD menunjukkan semua seramik BCZT mempunyai fasa tunggal yang stabil dengan struktur hablur tetragon. Walaupun seramik Ba(Zr0.025Ti0.975)O3 (BZT) tulen (x = 0.000) menunjukkan ketumpatan tertinggi iaitu 98.0%, saiz butiran yang paling besar diperoleh bagi seramik BCZT dengan komposisi x = 0.025. Seramik BCZT dengan penggantian Ca yang terendah menunjukkan sifat piezoelektrik dan feroelektrik yang lebih baik berbanding seramik dengan kandungan Ca yang lebih tinggi. Ujian medan elektrik berulang menunjukkan kestabilan dinamik serta sifat kebangkitan bagi seramik BCZT dengan x = 0.025 dan 0.050.

 

Kata kunci: BaTiO3 dan titanat; medan elektrik berulang; sifat piezoelektrik; tindak balas keadaan pepejal

 

Abstract

This research was conducted to study the effects of lower Ca substitution on the ferroelectric properties of (Ba1-xCax)(Zr0.025Ti0.975)O3 (BCZT) ceramics. BCZT ceramics were prepared using the solid-state reaction method and sintered at 1350 °C for 2 h. XRD analysis shows that all BCZT ceramics have a stable single phase with tetragonal crystal structure. Although pristine Ba(Zr0.025Ti0.975)O3 (BZT) ceramic (x = 0.000) displays the highest density of 98.0%, the largest grain size was obtained in BCZT ceramics with x = 0.025. BCZT ceramic with the lowest Ca substitution exhibits better piezoelectric and ferroelectric properties compared to ceramics with higher Ca contents. The repetitive electric fields test shows the dynamic stability and wake-up behavior for BCZT ceramics with x = 0.025 and 0.050.

 

Keywords: BaTiO3 and titanates; piezoelectric properties; repetitive electric fields, solid state reaction

 

RUJUKAN

Acosta, M., Novak, N., George, J. & Rödel, J. 2015. Mechanisms of electromechanical response in (1-x)Ba(Zr0.2Ti0.8)O3-x(Ba0.7Ca0.3)TiO3 ceramics. Applied Physics Letters 107: 142906-5.

Bai, W.F., Chen, D.Q., Li, P., Shen, B., Zhai, J.W. & Ji, Z.G. 2016. Enhanced electromechanical properties in <00l>-textured (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3 lead-free piezoceramics. Ceramics International 42: 3429-3436.

Castkova, K., Maca, K., Cihlar, J., Hughes, H., Matoušek, A., Tofel, P., Bai, Y. & Button, T.  2015. Chemical synthesis, sintering and piezoelectric properties of Ba0.85Ca0.15Zr0.1Ti0.9O3 lead-free ceramics. Journal of the American Ceramic Society 98(8): 2273-2280.

Coondoo, I., Panwar, N., Alikin, D., Bdikin, I., Islam, S.S., Turygin, A., Shur, V.Y. & Kholkin A.L. 2018. A comparative study of structural and electrical properties in lead-free BCZT ceramics: Influence of the synthesis method. Acta Materialia 155: 331-342.

Dai, B., Hu, X., Yin, R., Bai, W., Wen, F., Deng, J., Zheng, L., Du, J., Zheng, P. & Qin, H. 2017. Piezoelectric grain-size effects of BaTiO3 ceramics under different sintering atmospheres. Journal of Materials Science: Materials in Electronics 28: 7928-7934.

Fan, Z., Koruza, J., Rödel, J. & Tan, X. 2018. An ideal amplitude window against electric fatigue in BaTiO3-based lead-free piezoelectric materials. Acta Materialia 151: 253-259.

França, E., Romanholo, P., Simões, S., Falcão, E., Franco, A. & Machado, F. 2021. Enhancing the electrical properties of NBT ceramics by the addition of small amounts of Yb. Journal of Alloys and Compounds 873: 159845-7.

Fu, D. & Itoh, M. 2015. Role of Ca off-centering in tuning ferroelectric phase transitions in Ba(Zr,Ti)O3 system. Ferroelectric Materials - Synthesis and Characterization. First ed. Croatia. InTech.

Gao, J., Hu, X., Zhang, L., Li, F., Zhang, L., Wang, Y., Hao, Y., Zhong, L. & Ren, X. 2014. Major contributor to the large piezoelectric response in                                                                     (1-x)Ba(Zr0.2Ti0.8)O3-x(BaCa0.3)TiO3 ceramics: Domain wall motion. Applied Physics Letters 104(205): 252909-5.

Genenko, Y.A., Glaum, J., Hoffmann, M.J. & Albe, K. 2015. Mechanisms of aging and fatigue in ferroelectrics. Materials Science and Engineering: B 19: 52-82.

Guo, F.Y., Cai, W., Gao, R.L., Fu, C.L., Chen, G., Deng, X.L., Wang, Z.H. & Zhang, Q.W. 2019. Microstructure, enhanced relaxor like behavior and electric properties of (Ba0.85Ca 0.15)(Zr0.1-xHfxTi0.9)O3 ceramics. Journal of Electronic Materials 48: 3239-3247.

Hao, J., Li, W., Zhai, J. & Chen, H. 2018. Progress in high-strain perovskite piezoelectric ceramics. Materials Science and Engineering: R: Reports 135: 1-57.

Izzuddin, I., Jumali, M.H.H., Zalita, Z., Huwaida, J.N. & Awang, R. 2016. Influence of crystal structural orientation on impedance and piezoelectric properties of KNN ceramic prepared using sol-gel method. Sains Malaysiana 45(8): 1281-1287.

Jamil, N.H.J. 2022. Kebangkitan sifat feroelektrik dalam seramik-fero bebas plumbum BaTiO3 dengan ubah suai unsur Ca dan Zr. Tesis Dr. Fal, Jabatan Fizik Gunaan, Fakulti Sains dan Teknologi, Universiti Kebangsaan Malaysia (Tidak diterbitkan).

Jamil, N.H.J., Zainuddin, Z., Jumali, M.H.H., Izzuddin, I. & Nadzir, L. 2022. Tetragonal tungsten bronze phase potential in increasing the piezoelectricity of sol-gel synthesized (K0.5Na0.5)1-xLixNbO3 ceramics. Ceramics International 48(7): 9324-9329.

Jamil, N.H.J., Jumali, M.H.H., Zainuddin, Z., Izzuddin, I. & Pojprapai, S. 2019. Penentuan parameter optimum bagi rawatan pengutuban elektrik ke atas seramik-piezo (BaTiO3) menggunakan sistem buatan sendiri. Sains Malaysiana 48(2): 425-433.

Jian, X., Lu, B., Li, D., Yao, Y., Tao, T., Liang, B., Guo, J., Zeng, Y., Chen, J. & Lu, S. 2018. Direct measurement of large electrocaloric effect in Ba(ZrxTi1-x)O3 ceramics. ACS Applied Materials & Interfaces 44(16): 19764-19770.

Jumali, M.H.H., Mohd, M.R., Wee, N.Y., Yahaya, M. & Salleh, M.M. 2010. Kelakuan pengesanan tekanan bagi seramik natrium bismut titanat. Sains Malaysiana 39(4): 621-626.

Kang, S.J.L. 2005. Sintering; Densification, Grain Growth and Microstructure. First ed. Oxford: Butterworth-Heinemann.

Kang, W., Zheng, Z., Li, Y. & Zhao, R. 2019. Study on piezoelectric, dielectric and dispersive phase transition of BaTiO3–BaZrO3–CaTiO3 ceramics. Journal of Materials Science: Materials in Electronics 30(17): 16244-16250.

Li, S.B., Wang, C.B., Li, L., Shen, Q. & Zhang, L.M. 2018. Effect of annealing temperature on structural and electrical properties of BCZT ceramics prepared by plasma activated sintering. Journal of Alloys and Compounds 730: 182-190.

Liu, W. & Ren, X. 2009. Large piezoelectric effect in Pb-free ceramics. Physical Review Letters 103: 257-602.

Liu, Y., Chang, Y., Sun, E., Li, F., Zhang, S., Yang, B., Sun, Y., Wu, J. & Cao, W. 2018. Significantly enhanced energy harvesting performance and superior fatigue-resistant behavior in [001]c-textured BaTiO3 based lead-free piezoceramics. ACS Applied Materials & Interfaces 10(37): 31488-31497.

Liu, Y.C., Chang, Y.F., Li, F., Yang, B., Sun, Y., Wu, J., Zhang, S.T., Wang, R.X. & Cao, W.W. 2017. Exceptionally high piezoelectric coefficient and low strain hysteresis in grain-oriented (Ba,Ca)(Ti,Zr)O3 through integrating crystallographic texture and domain engineering. ACS Applied Materials & Interfaces 9: 29863-29871.

Mane, S., Tirmali, P. & Kulkarni, S. 2018. Hybrid microwave sintering and shifting of Tc in lead-free ferroelectric composition x(Ba0.7Ca0.3TiO3)-(1-x)(BaZr0.2Ti0.8O3). Materials Chemistry and Physics 213: 482-491.

Mondal, T., Majee, B.P. & Das, S. 2017. A comparative study on electrical conduction properties of Sr-substituted Ba1-xSrxZr0.1Ti0.9O3 (x = 0.00-0.15) ceramics. Ionics 23: 2405-2416.

Öksüz, K., Sen, S. & Sen, U. 2015. Microstructural evaluation and characterization of solid- state reaction of B2O3 doped BaZrxTi1-xO3 ceramics. Journal of the Australian Ceramic Society 51: 137-143.

Parhi, C.C., Thirumalasetty, A.B., James, A.R. & Wuppulluri, M. 2023. Relative investigation on microwave-assisted Zr-modified PbTiO3 and BaTiO3 ferroelectric ceramics for energy storage application. ACS Omega 8(41): 37752-37768.

Premkumar, S., Sarangapani, R. & Mathe, V. 2021. Understanding the A and B-site engineered lead-free Ba(1-x)CaxZryTi(1−y)O3 piezoceramics: A perspective from DFT. Journal of Materials Chemistry C 9: 4248-4259.

Promsawat, M., Deluca, M. Kampoosiri, S. Marungsri, B. & Pojprapai, S. 2017. Electrical fatigue behavior of lead zirconate titanate ceramic under elevated temperatures. Journal of the European Ceramic Society 37(5): 2047-2055.

Rojas, V., Koruza, J., Patterson, E. A., Acosta, M., Jiang, X., Liu, N., Dietz, C. & Rödel, J. 2017. Influence of composition on the unipolar electric fatigue of Ba(Zr0.2Ti0.8)O3-(Ba0.7Ca0.3)TiO3 lead-free piezoceramics. Journal of the American Ceramic Society 100(10): 4699-4709.

Reyes-Montero, A., Ramos-Alvarez, P., González, Amador, López-Juárez, R. & María-Elena, V. 2017. Dielectric and impedance analysis on the electrical response of lead-free Ba1−xCaxTi0.9Zr0.1O3 ceramics at high temperature range. Applied Sciences 7(3): 214.

Sagdeo, A., Nagwanshi, A., Pokhriyal, P., Sinha, A., Rajput, P., Mishra, V. & Sagdeo, P. 2018. Disappearance of dielectric anomaly in spite of presence of structural phase transition in reduced BaTiO3: Effect of defect states within the bandgap. Journal of Applied Physics 123(16): 161424-8.

Sawangwan, N., Barrel, J., Mackenzie, K. & Tunkasiri, T. 2008. The effect of Zr content on electrical properties of Ba(Ti1−xZrx)O3 ceramics. Applied Physics A: Materials Science and Processing 90: 723-727.

Shi, X., Hoffman, M. & Kumar, N. 2020. Electrical fatigue behavior of NBT-BT-xKNN ferroelectrics: Effect of phase transformations and oxygen vacancies. Journal of Materials Chemistry C 8: 3887-3896.

Xu, Q. & Li, Z. 2020. Dielectric and ferroelectric behaviour of Zr-doped BaTiO3 perovskites. Processing and Application of Ceramics 14(3): 188-194.

Yingwei, L. Xiangyang, C., Dapeng, Z. & Zhipeng, G. 2020. Influence of domain switching process on the electrical fatigue behavior of ferroelectrics. Ceramics International 46(15): 24213-24224.

Yuan, R., Xue, D., Zhou, Y., Ding, X., Juan, L. & Xue, D. 2017. Ferroelectric, elastic, piezoelectric, and dielectric properties of Ba(Ti0.7Zr0.3)O3-x(Ba0.82Ca0.18)TiO3 Pb-free ceramics. Journal of Applied Physics 122(4): 044105.

Zhang, Q., Cai, W., Li, Q., Gao, R., Chen, G., Deng, X., Wang, Z., Cao, X. & Fu, C. 2019. Enhanced piezoelectric response of (Ba,Ca)(Ti,Zr)O3 ceramics by super large grain size and construction of phase boundary. Journal of Alloys and Compounds 794: 542-552.

Zhang, Y., Glaum, J., Ehmke, M., Blendell, J., Bowman, K. & Hoffman, M. 2016. High bipolar fatigue resistance of BCTZ lead-free piezoelectric ceramics. Journal of the American Ceramic Society 99(1): 174-182.

Zhenhua L., Sirirat, K., Thita, S., Watcharin, J., Boonruang, M. & Soodkhet, P. 2021. A study of the electrical fatigue behavior of lead zirconate titanate for micro-actuator application in hard disk drives. Integrated Ferroelectrics 214(1): 11-18.

Zolkepli, M.F.A.B. & Zainuddin, Z. 2017. Structural, magnetic and electrical properties of barium titanate and magnesium ferrite composites. Sains Malaysiana 46(6): 967-973.

 

*Pengarang untuk surat-menyurat; email: hafizhj@ukm.edu.my

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

sebelumnya